How to Configure a Basic ACL Rule on Huawei S5700?

Questions:
How to configure a Basic ACL Rule on S5700 Huawei?

Answer:
Procedure
Run:system-view,The system view is displayed.
Run:acl [ number ] acl-number,A numbered basic ACL is created and the basic ACL view is displayed.
Run:acl name acl-name { basic | acl-number },A named basic ACL is created and the basic ACL view is displayed.
Run:rule [ rule-id ] { deny | permit } [ source { source-address source-wildcard | any } | fragment | logging | time-range time-name ] ,A basic ACL rule is configured. To configure multiple rules, repeat this step.
Run:rule rule-id description description,The description of a basic ACL rule is configured.

NOTE:
If the rule ID is not specified, the step value is used as the start rule ID.
If the time range is specified, the time range name must be configured. Otherwise, the rule does not take effect.

Huawei S5700 Price and Specification: http://www.huanetwork.com/huawei-switch-s5700-series-price_c79

How to Configure RMON Statistics Functions on Huawei S2700?

Questions:
How to configure RMON Statistics Functions on Huawei Quidway S2700 Huawei Switches ?

Answer:
Procedure
Run:system-view,The system view is displayed.
Run:interface { ethernet | gigabitethernet } interface-number,The interface view is displayed.
Run:rmon-statistics enable,RMON statistics function is enabled on an interface.
Run:rmon statistics entry-number [ owner owner-name ],A statistics table is created and an entry is added to the table.
Run:system-view,The system view is displayed.
Run:interface { ethernet | gigabitethernet } interface-number,The interface view is displayed.
Run:rmon-statistics enable,RMON statistics function is enabled on an interface.
Run:rmon history entry-number buckets number interval sampling-interval  [ owner owner-name  ],A history control table is created and an entry is added to the table.

 NOTE:
-As recommended by the RMON specifications, each monitored interface should be configured with more than two history control entries. One entry is sampled every 30 seconds while another entry is sampled every 30 minutes.
-The short sampling interval enables a monitor to probe the sudden changes of traffic modes, and the long sampling interval is applicable if the interface status is relatively stable.
-Each history control table stores 10 records. When more records are generated, the old ones are overwritten.
-To reduce the impact of RMON on system performance, the sampling interval of the history control table should be longer than 10 seconds. In addition, an interface cannot be configured with too many entries for the history control table and alarm table.
-If the RMON statistics function is not enabled on an interface, statistics in the RMON statistics table and history table are 0.

Huawei wholesale Huawei S2700 Price and Specification: http://www.huanetwork.com/huawei-switch-s2700-series-price_c77

How to Configure flow control function on Huawei S2700?

Questions:
How to configure flow control function on S2700 Huawei?

Answer:
Procedure
Run:system-view,The system view is displayed.
Run:interface interface-type interface-number,The interface view is displayed.
Run:flow-control,The flow control function is enabled.By default, flow control is disabled on an Ethernet interface.

NOTE:
Flow control takes effect when the flow control function is enabled for interfaces on both ends of a link.

Huawei S2700 Price and Specification:http://www.huanetwork.com/huawei-switch-s2700-series-price_c77

How to Configure Access Control Mode of an Interface on Huawei S5700?

Questions:
How to configure Access Control Mode of an Interface Huawei Quidway S5700?

Answer:
Procedure
Run:system-view,The system view is displayed.
Run:dot1x port-method { mac | port } interface { interface-type interface-number1 [ to interface-number2 ] } &<1-10>,The access control mode of the interface is configured.
Run:interface interface-type interface-number,The interface view is displayed.
Run:dot1x port-method { mac | port },The access control mode of the interface is configured.

NOTE:
When 802.1x authentication users are online, you cannot change the access control mode of an interface.

Huawei S5700 Price and Specification: http://www.huanetwork.com/huawei-switch-s2700-series-price_c77

WS-C3560X-48PF-L datasheet

Switching Fabric 160 Gbps DRAM Catalyst 3560X  256 MB Flash 64 MB Total VLANs 1005 VLAN IDs 4K Total Switched Virtual Interfaces 1K Jumbo Frame 9216 Byte Total Routed Ports 468 Forwarding Rate 101.2 mpps Unicast MAC addresses Access:4K  Default:6K Routing:3K  VLAN:12K IGMP groups and multicast routes Access:1K  Default:1K  Routing:1K VLAN:1K Unicast routes Access:6K  Default:8K  Routing:11K  VLAN:0K Directly connected hosts Access:4K  Default:6K  Routing:3K  VLAN:0K Indirect routes Access:2K  Default:2K  Routing:8K  VLAN:0K Policy-based routing ACEs Access:0.5K  Default:0K  Routing:0.5K  VLAN:0K QoS classification ACEs Access:0.5K Default:0.5K  Routing:0.5K  VLAN:0.5K Security ACEs Access:2K  Default:1K Routing:1K  VLAN:1K VLANs Access:1K  Default:1K  Routing:1K  VLAN:1K Dimensions (H x W x D) 1.75 x 17.5 x 19.5in. (4.45 x 44.5 x 49.5 cm)  Weight 16.6lb (7.5 kg) Mean Time Between Failure Hours 149,594 Relative Humidity 5% to 95%,noncondensing Storage Environment Temperature: -40 C' to 70 C' Altitude: 15,000 ft Vibration Operating: 0.41Grms from 3 to 500Hz with spectral break points of 0.0005 G2/Hz at 10Hz and 200Hz 5dB/octave roll off at each end. Nonoperating: 1.12Grms from 3 to 500Hz with spectral break points of 0.0065 G2/Hz at 10Hz and 100Hz 5dB/octave roll off at each end. Shock Operating: 30G, 2ms Half sine Nonoperating: 55G, 10ms Trapezoid

Management  

BRIDGE-MIB CISCO-CDP-MIB

CISCO-CLUSTER-MIB CISCO-CONFIG-MAN-MIB

CISCO-ENTITY-FRU-CONTROL-MIB CISCO-ENVMON-MIB

CISCO-FLASH-MIB CISCO-FTP-CLIENT-MIB

CISCO-HSRP-MIB CISCO-HSRP-EXT-MIB

CISCO-IGMP-FILTER-MIB CISCO-IMAGE-MIB

CISCO-IP-STAT-MIB CISCO-L2L3-INTERFACE-CONFIG-MIB

CISCO-POE-EXTENSIONS-MIB CISCO-MAC-NOTIFICATION-MIB

CISCO-MEMORY-POOL-MIB CISCO-PAGP-MIB

CISCO-PING-MIB CISCO-PROCESS-MIB

CISCO-RTTMON-MIB CISCO-STP-EXTENSIONS-MIB

CISCO-SYSLOG-MIB CISCO-TCP-MIB

CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB CISCO-VLAN-MEMBERSHIP-MIB

Standards

IEEE 802.1s

IEEE 802.1w

IEEE 802.1x

IEEE 802.1x-Rev

IEEE 802.3ad

IEEE 802.1ae

IEEE 802.3af

IEEE 802.3at

IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T ports

IEEE 802.1D Spanning Tree Protocol

IEEE 802.1p CoS Prioritization

IEEE 802.1Q VLAN

IEEE 802.3 10BASE-T specification

IEEE 802.3u 100BASE-TX specification

IEEE 802.3ab 1000BASE-T specification

IEEE 802.3z 1000BASE-X specification

More information about WS-C3560X-48PF-L, please click here http://www.3anetwork.com/cisco-ws-c3560x-48pf-l-price_p60.html

How to Configure NAP master device on Huawei S5700?

Questions: 
How to Configure NAP master device on Huawei Quidway S5700?

Answer: 
Procedure
Run:system-view The system view is displayed.
Run:interface interface-type interface-number The interface view is displayed.
Run:nap login neighbor The login to the slave device from the master device is performed.
If the slave device has an empty configuration, you can log in to the slave device from the master device without a user name and a password.
If, however, the slave device is configured with user name(s) and password(s), you must enter the correct user name and password to perform a NAP-based remote login to the slave device.

NOTE:
To ensure security for NAP, the slave device having an empty configuration checks the source address of the Telnet login. If the Telnet source address is the NAP address of the master device that is telnetting to the slave device, the slave device allows the master device to directly log in without being authenticated. This is because by default, the user level of the remote login based on the NAP address is the same as the login through the console interface, which enjoys the highest user level. If the Telnet source address is not the NAP address of the master device, the remote login fails.
If ip source check user-bind enable command is executed on an interface, the interface cannot connect to the NAP neighbor.

.Huawei S5700 Price and Specification: http://www.huanetwork.com/huawei-switch-s5700-series-price_c79

S2700-26TP-EI-AC description

Huawei Quidway Switch S2700, S2700-26TP-EI Mainframe(24 10/100 BASE-T ports and 2 Combo GE(10/100/1000 BASE-T+100/1000 Base-X) ports and AC 110/220V)
• AC Power

• Non-POE Switch

• Layer 2 Ethernet Switch

• Port: 24 FE ports, 2 GE Combo ports

• Software: Enhanced Version

• Auto Configure

• HGMP group management

• Embedded 6 KV surge protection

• 802.1x and MAC address authentication

The S2700 series enterprise switches are next-generation energy-saving intelligent 100M Ethernet switches. The S2700 utilizes cutting-edge switching technologies and Huawei Versatile Routing Platform (VRP) software to meet the demand for multi-service provisioning and access on Ethernet networks. It is easy to install and maintain and can be used in a variety of enterprise network scenarios. With its flexible VLAN deployment, comprehensive security and QoS policies, and energy-saving technologies, the S2700 helps enterprise customers build next-generation S6700-24-EI IT networks.

S2700-18TP-EI-AC datasheet

Huawei Quidway Switch S2700, S2700-18TP-EI Mainframe(16 10/100 BASE-T ports and 2 Combo GE(10/100/1000 BASE-T+100/1000 Base-X) ports and AC 110/220V)

• AC Power

• Non-POE Switch

• Layer 2 Ethernet Switch

• Port: 16 FE ports, 2 GE Combo ports

• Software: Enhanced Version

• Auto Configure

• HGMP group management

• Embedded 6 KV surge protection

• 802.1x and MAC address authentication

The S2700 series enterprise switches are next-generation energy-saving intelligent 100M Ethernet switches. The S2700 utilizes cutting-edge switching technologies and Huawei Versatile Routing Platform (VRP) software to meet the demand for multi-service provisioning and access on Ethernet networks. It is easy to install and maintain and can be used in a variety of enterprise network scenarios. With its flexible VLAN deployment, comprehensive security and QoS policies, and energy-saving technologies, the S2700 helps enterprise customers build next-generation S2700-26TP-EI-AC IT networks.

SF300-24 Layer 3 mode routing problem 12-12-17

Question

SF300-24 routing. S5700-52C-SI That's network configuration:

Port 1 to 12 assigned to VLAN 10

Port 13 to 23 assigned to VLAN 20

Port 24 has an ip 10.17.7.254 to connect with my deafult route, beacuse also a Linksys RV042 router, connected in turn with my ISP router, having an ip 10.17.7.1.

VLAN 10 has 10.17.10.1

VLAN 20 has 10.17.20.1

So add a default route on SF300-24 to 10.17.7.1 to get Internet connection.

That's the problem:

Computer A is connected to VLAN 10 on port 1

Compuer B is connected to VLAN 20 on port 13

A e B can talk perfectly each other, and also to port 24 (10.17.7.254), but when I try to ping my Linksys RV042 (10.17.7.1) or reach Internet everything fail.

Instead when I logged into SF300-24 and try to ping Linksys RV042 (10.17.7.1) or reach the Internet, everything works fine!

Answer:

Yes, need to set up S5700-28C-EI static routes on the router.

. Huawei Launches Industry's First ultra-high density cassette switch S5710-HI

In the United States Interop show,S2700-26TP-EI-DC Huawei launched the industry's first ultra high density magnetic switch S5710-HI. The switches support 4X40G uplink interface, with up to 108 physical port, the port density is 2 times that of the similar product in the industry, is the first choice for large and medium-sized high-end quality of campus network access, small convergence campus network and data center access.

With the development of cloud computing, BYOD, terminal and access intranet more rich, the number of users access to more and more, for the performance of network bandwidth, equipment reliability, maintainability and put forward higher requirements. How to protect users investment basis, to maximize the efficient and stable operation of the network to ensure the park? According to the enterprise park Gigabit access scenario, Huawei launched S5710-HI switches, providing flexible full Gigabit access and Gigabit /4 Gigabit uplink port. The series switches based on the unity of the new generation of high performance hardware and Huawei Company VRP (Versatile Routing Platform) software platform, has high density flexible port combination, easy operation and maintenance, perfect VPN tunnel, outstanding network flow analysis, 48 port device 30W POE power supply capacity, fully meet the user density access requirements, and to provide users with network security robust and high quality services.

Gigabit Ethernet access switches as a cost-effective "mini frame", Huawei S5710-HI has four expansion slots, can realize 48*GE (electric) 48GE 8*10GE4*40GE (light), 96GE (electric) 8*10GE 4*40GE, or 96*GE (electric) 12*10GE different port combination, fully meet the actual needs of different users of the bandwidth upgrade, to protect users investment. Huawei S5710-108C-PWR-HI also can be used as high quality enterprise dedicated access equipment, the industry is one of the few high Xingjiebi cassette MPLS switch. Increase in performance at the same time, Huawei S5710-HI support equipment Zero Configuration start, fault equipment from configuration change, thus simplifying the enterprise network deployment and maintenance, help enterprise S2700-26TP-SI-AC users to achieve easy network operation and maintenance.

Function of S5352C-PWR-SI Port

Huawei Quidway Switch S5300, S5352C-PWR Mainframe(48 10/100/1000Base-T ports and supports 2 10GE XFP subcards, 4 1000Base-X SFP subcards, 2 10GE SFP+ subcards, and 4 10GE SFP+ subcards,PoE,Chassis,Dual Slots of power,Without Flexible Card and Power Module)

Quidway S5300 series gigabit switches are new generation Ethernet gigabit switches that meet the requirements for high-bandwidth access and Ethernet multi-service convergence, providing powerful Ethernet functions for operators and enterprise customers. Based on the new generation high-performance hardware and Huawei Versatile Routing Platform (VRP), the S5300 features large capacity and gigabit interfaces of high density, provides 10G uplinks, meeting the requirements for the 1G and 10G uplink devices of high density. The S5300 can meet the requirements of multiple scenarios such as service convergence on campus networks and Intranets, the access to the IDC at a rate of 1000 Mbit/s, and the access to computers S5352C-EI at a rate of 1000 Mbit/s on Intranets.

Huawei S5700-EI Comprehensive reliability mechanisms

The S5700-EI supports enhanced S5352C-EI trunk (E-Trunk) that enables a CE to be dual-homed to two PEs (S5700s). E-Trunk greatly enhances link reliability between devices and implements link aggregation between devices. This improves reliability of access devices.

The S5700-EI supports the Smart Ethernet Protection (SEP) protocol, a ring network protocol applied to the link layer on an Ethernet network. SEP can be used on open ring networks and can be deployed on upper-layer aggregation devices to provide fast switchover (within 50 ms), ensuring non-stop transmission of services. SEP features simplicity, high reliability, fast switchover, easy maintenance, and flexible topology, facilitating network planning and management.

The S5700-EI supports VRRP, and can set up VRRP groups with other Layer 3 switches. VRRP provides redundant routes to ensure stable and reliable communication. Multiple equal-cost routes to an uplink device can be configured on the S5700-EI to provide route redundancy. When an active route is unreachable, traffic is switched to a backup route.

The S5700-EI supports BFD, which provides millisecond-level fault detection for protocols such as OSPF, IS-IS, VRRP, and PIM to improve network reliability. Complying with IEEE 802.3ah and 802.1ag, the S5700-EI supports point-to-point Ethernet fault management and can detect faults in the last mile of an Ethernet link to users.

Several S5700s can be stacked to provide a 1000 Mbit/s access rate for terminals. Only four pairs of optical fibers are required to connect the stack to uplink devices. This reduces the number of optical fibers and ports needed on uplink devices and enhances network S5352C-PWR-SI reliability.

Huawei Enterprise S5700-EI

The Huawei S57EI series gigabit S5700-52C -SI enterprise switches (S57EI) are next-generation energy-saving switches developed by Huawei to meet the demand for high-bandwidth access and Ethernet multi-service aggregation. Based on the cutting-edge hardware and Huawei Versatile Routing Platform (VRP) software, the S57EI provides a large switching capacity and high-density GE ports to implement 10 Gbit/s upstream transmissions. The S57EI is for use in various enterprise network scenarios. For example, it can function as an access or aggregation switch on a campus network, a gigabit access switch in an Internet data center (IDC), or a desktop switch to provide 1000 Mbit/s access for terminals. The S57EI is easy to install and maintain, reducing workloads for network planning, construction, and maintenance. The S57EI uses advanced reliability, security, and energy conservation technologies, helping enterprise customers build a next generation IT network.

The S5700 can function as an access device on a large-sized enterprise network or an aggregation device on a small-or medium-sized campus network. It supports link aggregation and dual-homing S5700-24TP-PWR-SI to improve network reliability.

SLM2048

Am using the SLM 2048 as my core S2700-18TP-EI-AC switch in a small environment,for distribution switch I have ESW520, SRW2048,catalyst 2960 and another SLM2048.
Each of the distribution switches has a single link to the core.

Prior to deployment I configured a management IP address on the distribution switches but I did not on the core switch.Now I find it difficult to connect to the web page and assign a management ip on the core switch
Sent from Cisco Technical Support iPad App

Just out of interest, are these the End of sale  SLM2048 Linksys branded switches or the replacement new technology cisco branded switch with part number SLM2048T-NA   ?

You have to be able to get to the management interface.  The smart switch has only a GUI interface with a default IP qaddress assigned, if you don't alter the default address.

I would suggest you grab to quickstart guide for you product, which is freely downloadable.

The quickstart guide for the newer product, SLM2048T-NA says;

In order to access the switch with a web-based interface, you must know the management IP address of the switch. The default configuration of the switch is to use its factory default IP address of 192.168.1.254 until it has obtained an IP address from a DHCP server, or it has been changed to a static IP address.
When the switch is using the factory default IP address, its System LED flashes continuously.

for this newe switch, you have to place a PC in that network  and access the GUI or find out of the switch received a IP address via DHCP.  You may find that you may have to, if possible , reduce the network complexity and switch connections and try to access the switch GUI maybe afterhours.

If it's under warranty, S2700-26TP-EI-AC you can try http://www.cisco.com/go/sbsc to see if there is a problem with the management interface.

Console cable for SRW2048

lost the original console cable to the Cisco Linksys SRW2048 and was wondering if I can use the Cisco console cable or can a regular serial cable with female ends will work?
A cisco console cable probably won't work since they usually have RJ-45 on one end.  However, a regular serial cable should work just fine, as long as your computer has one as well, or you have a USB to serial adapter.

The settings for the console port are as follows:
Bits per second: 38,400
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None

Once you open the connection you'll have to hit enter once to make anything display.

You can also acces the console of this switch through telnet, by connecting to the switches IP with a telnet client and use admin as the username with a blank password.

I got most of this info from the admin guide, which is available here:
http://www.cisco.com/en/US/docs/switches/lan/csbms/srw2048/administration/guide/SRW-US_v10_UG_A-Web.pdf